A solenoid is a simple rugged device providing the interface between the electronics and mechanicals actuation in many types of equipment.
Its component parts consist of a coil (to carry current and generate ampere turns), an iron shell or case (to provide a magnetic circuit), and a movable plunger or pole (to act as the working element).
Many of our solenoids have an auxiliary flux path, not normally found in conventional solenoids, which provides a significant increase in force.
A major objective in the design of a solenoid is to provide an iron path capable of transmitting maximum magnetic flux density with a minimum energy input.
The purpose of a solenoid is to get the best relationship between the variable ampere turns and the working flux density in the air gap.
The working gaps flux density can be increased by increasing the electrical input to the coil. However as the electrical input increases the coil temperature rises and the work output is reduced. The amount by which the electrical input can be increased depends upon the relative duty cycle and maximum allowable coil temperature.
- The magnetic flux generated is dependent on the number of turns and the current developed when power is applied to the coil. The permissible temperature rise limits the magnitude of the power input.
- Working flux density is the total magnetic flux divided by the magnetic path (iron path) area.
- The air gap, the iron path, the pole piece and its contour determine the working flux density.
High torques/forces may be obtained from a solenoid if it is used infrequently.
- The ON and OFF sequence is the time factor which determines the permissible watts input.
- The formula to calculate the relative duty cycle is:
RELATIVE DUTY CYCLE % = (ON TIME / (ON + OFF TIME) x 100
Continuous operation should not be confused with continuous duty cycle.
- The continuous duty cycle (100% rating) means that the solenoid can be left energised for an indefinite period of time at its rated voltage without overheating.
- For continuous operation where the solenoid is switched ON and OFF repeatedly, a higher torque/force can be achieved but the permissible ON/OFF time periods for each relative duty cycle % must not be exceeded.
The following diagram indicates the relationship between and ‘on’ and ‘off’ time
An alternative method of increasing the torque/force output is to use a continuous 100% duty cycle rated solenoid and apply an over voltage input for a short period of time and then reduce the voltage across the solenoid coil to the 100% duty rated voltage for the hold-on period.
Influence on over voltage on the solenoid’s characteristic.
a = characteristic with normal voltage
b = holding force with normal voltage
c = effect of over voltage
W1 = available work output at normal voltage
W2 = additional work output available by over voltage
The method of achieving an increased torque/force and a continuous 100% rating for hold-on is to use an economy circuit which switches a resistor in series with the solenoid coil when the operating stroke is completed and the plunger has reached its hold-on position. The conditions which apply during operation are as follows.
Plunger in start position and during operation:
P1 = (l1) 2Rs Where l1 = V / Rs
Plunger in end position (hold-on)
P2 = (I2) 2Rs Where I2 = V / Rs + Re
P1 = Solenoid input power at start
P2 = Solenoid input power at hold-on
Rs = Solenoid coil resistance
Re = Series economy resistance
V = Input supply voltage
The value of Re must be designed to give a solenoid input power equal to the rated 100% ED power value when switched in series.
The time taken for a solenoid to complete its energised stroke is measured from the moment a voltage is applied to the time the energised position is achieved.
- This time is dependent upon the load, duty cycle, input power, stroke and temperature range. When a DC voltage is applied the current will rise to point (a) as illustrated below.
- This time delay occurs prior to any plunger motion until sufficient flux is developed to overcome the load.
- As the plunger moves through its stroke the change in inductance resulting from the closing air gap causes a dip in the current trace until the solenoid has completed its stroke. From here the current trace begins to rise to a steady state current value which by Ohms law is I = V / R
At point (a) the solenoid has developed sufficient flux to move the load, as the load increases, more time is required to reach point (c), as shown by the phantom trace.
If the load increased beyond the performance value of the Solenoid the coil will build immediately to a steady state current, no dip will occur as no plunger movement has taken place (top curve).
- Published torque and forces are specified at an ambient temperature of 20°C.
- DUTY CYCLE is given at 100% of the rated voltage a reference temperature of +35°C and a cycle time of 5 minutes maximum, with solenoids mounted in an unrestricted flow of air.
- POWER RATING is the wattage consumed operating at the rated duty cycle and at 20°C coil temperature.
- AMBIENT TEMPERATURE range -50°C to +35°C.
- COIL INSULATION CLASSIFICATIONS
Insulating materials used with solenoids are classified according to their stability during constant heating.
The following table illustrates the insulation classes available for our solenoid ranges.
||Maximum Coil Temperature °C
||Maximum temperature rise above 35°C ambient
||Applicable solenoid type
||Open frame Magnetic latching Tubular
||Open frame* Magnetic latching*
||Rotary Stepper Low Profile
||Rotary* Stepper* Low Profile*
* High-temperature insulation is available to special order depending on solenoid type and volumes.
Technical Considerations for Ordering Solenoids
The performance published in our data sheets is for guidance only, as varying electrical, mechanical and environmental conditions will have an effect.
To enable us to help you choose and specify the correct solenoid to suit your application, please use the following information to detail your requirement.
||Specify maximum envelope available. Remember the larger the solenoid the lower the current and operation costs.
|Force or Torque Required
||Specify initial requirements
Stroke is expressed in degrees of rotation for Rotary Solenoids and movement in mm for Linear Solenoids. Specify direction and angle of rotation (viewed on Armature Plate) for Rotary Solenoids
Specify Push or Pull operation and movement required for Linear Solenoids
||Duty cycle is expressed as a percentage of the on time in a total time taken for 1 cycle of operation. If in doubt specify maximum on time and minimum off time for 1 cycle
||Specify working voltage tolerances and any current limitations
||Specify working ambient temperature
To find out more, please contact our specialist Design & Engineering Team +44 (0)1535 661144 or email email@example.com